Page Header Logo Applied Science and Engineering Progress

Home > ONLINE FIRST > Nayeeif

Investigation of the Effects of Unbalance and Bearing Wear on Shaft Vibration in a Natural Gas Turbine Plant

Adil Abed Nayeeif, Ehsan S. Al-Ameen, Nazik Abdulwahid Jebur, Ahmed Ali Farhan Ogaili, Zahra Khalid Hamdan, Emad Kadum Njim

Abstract


This work investigates the effect of imbalance and bearing wear on the vibration of rotating shafts at a southern Iraqi natural gas liquefaction plant. This experimental study examines the impact of wear on couplings and uneven weight on the vibration of a two-stage gas turbine’s shaft, taking measurements during operation. The experimental procedure involves the use of proximity probes and the ADRE-408 Bentley Nevada system to measure vibrations along the X and Y axes. The study focuses on a two-stage gas turbine supported by four journal bearings and analyses the effects of coupling imbalance and erosion. The results show that adding 10 g and 20 g weights at 0° and 30° anticlockwise considerably increases the vibration amplitude, from 22.46 µm at 113.75 Hz to 24.35 µm at 117.5 Hz. Replacing worn couplings and bearings led to system stabilisation, vibration reductions, and a shift in critical frequencies. The data confirm that mass loss and bearing wear greatly affect the dynamics of rotating machinery. These findings emphasise the importance of predictive maintenance and diagnostic monitoring to prevent mechanical failures and maintain system stability.

Keywords



[1]      N. A. Jebur and W. A. Soud, “Fault diagnosis of journal bearings using vibration analysis and machine learning techniques,” Journal of Failure Analysis and Prevention, 2025, doi: 10.1007/s11668-025-02157-z.

[2]      A. A. F. Ogaili, A. A. Jaber, and M. N. Hamzah, “Wind turbine blades fault diagnosis based on vibration dataset analysis,” Data Brief, vol. 49, 2023, Art. no. 109414.

[3]      A. A. F. Ogaili, M. N. Hamzah, and A. A. Jaber, “Enhanced fault detection of wind turbine using extreme gradient boosting technique based on nonstationary vibration analysis,” Journal of Failure Analysis and Prevention, vol. 24, pp. 877–895, 2024, doi: 10.1007/s11668-024-01894-x.

[4]      A. A. F. Ogaili, Z. T. Al-Sharify, A. Abdulhady, and F. Abbas, “Vibration-based fault detection and classification in ball bearings using statistical analysis and random forest,” in Fifth International Conference on Green Energy, Environment, and Sustainable Development (GEESD 2024), 2024, pp. 518–526.

[5]      B. Djaidir, A. Hafaifa, and A. Kouzou, “Faults detection in gas turbine rotor using vibration analysis under varying conditions,” Journal of Theoretical and Applied Mechanics (Poland), vol. 55, no. 2, pp. 393–406, 2017, doi: 10.15632/ jtam-pl.55.2.393.

[6]      A. A. Nayeeif, M. A. Abdulrazzaq, and H. A. K. Ali, “Dynamic response study of the vibration of a washer,” AIP Conference Proceedings, vol. 2787, no. 1, 2023, doi: 10.1063/5.0149158.

[7]      H. I. Mansoora, M. Al-Shammari, and A. Al-Hamood, “Theoretical analysis of the vibrations in gas turbine rotor,” IOP Conference Series: Materials Science and Engineering, vol. 671, no. 1, 2020, Art. no. 012157, doi: 10.1088/1757- 899X/671/1/012157.

[8]      S. Aburakhia, I. Hamieh, and A. Shami, “Joint instantaneous amplitude-frequency analysis of vibration signals for vibration-based condition monitoring of rolling bearings,” 2024, doi: arXiv.2405.08919.

[9]      S. Chauhan, G. Vashishtha, R. Kumar, R. Zimroz, M. K. Gupta, and P. Kundu, “An adaptive feature mode decomposition based on a novel health indicator for bearing fault diagnosis,” Measurement, vol. 226, Feb. 2024, Art. no. 114191, doi: 10.1016/j.measurement. 2024.114191

[10]   X. A. Vasanth, P. S. Paul, G. Lawrance, and A. S. Varadarajan, “Vibration control techniques during turning process: A review,” Australian Journal of Mechanical Engineering, vol. 19, no. 1, pp. 1–20, 2021, doi: 10.1080/14484846.2019. 1585224.

[11]   A. Chaban, T. Perzyński, A. Popenda, R. Figura, and V. Levoniuk, “Mathematical modelling of transient processes in the susceptible motion transmission in a ship propulsion system containing a shaft synchronous generator,” Energies, vol. 15, no. 9, pp. 1–17, Apr. 2022, doi: 10.3390/en15093266.

[12]   S. M. Muyeen et al., “Comparative study on transient stability analysis of wind turbine generator system using different drive train models,” IET Renewable Power Generation, vol. 1, no. 2, pp. 131–141, Jun. 2007, doi: 10.1049/iet-rpg:20060030.

[13]   A. Hashemi, J. Jang, and S. Hosseini-Hashemi, “Smart active vibration control system of a rotary structure using piezoelectric materials,” Sensors, vol. 22, no. 15, pp. 1–22, 2022, doi: 10.3390/s22155691.

[14]   J. Bhattacharjee and S. Roy, “Smart materials for sustainable energy,” Natural Resources Conservation and Research, vol. 7, no. 1, pp. 1–12, 2024, doi: 10.24294/nrcr.v7i1.5536.

 X. Xie, J. Huang, and Z. Liang, “Vibration reduction for flexible systems by command smoothing,” Mechanical Systems and Signal Processing, vol. 39, no. 1–2, pp. 461–470, Aug. 2013, doi: 10.1016/j.ymssp.2013.02.021.

[15]   K. A. Mohammed, M. N. M. Al-Sabbagh, A. A. F. Ogaili, and E. S. Al-Ameen, “Experimental analysis of hot machining parameters in surface finishing of crankshaft,” Journal of Mechanical Engineering Research and Developments, vol. 43, no. 4, pp. 105–114, 2020, doi: 10.26480/ jmerd.04.2020.105.114.

[16]   M. Rahman, Z. C. Ong, W. T. Chong, S. Julai, and S. Y. Khoo, “Performance enhancement of wind turbine systems with vibration control: A review,” Renewable and Sustainable Energy Reviews, vol. 51, pp. 43–54, Nov. 2015, doi: 10.1016/j.rser.2015.05.078.

[17]   J. A. Andrawus, “Maintenance optimisation for wind turbines,” Ph.D. dissertation, The Robert Gordon University, Aberdeen, United Kingdom, 2008.

[18]   A. A. F. Ogaili, Z. T. Al-Sharify, A. A. Jaber, D. A. Farhan, and S. M. Al-Khafaji, “Effective ball bearing fault diagnosis leveraging ANN and statistical feature integration,” in Proceedings of the 10th Scholar’s Yearly Symposium on Technology, Engineering and Mathematics (SYSYEM 2024), 2024, vol. 3870, pp. 42–48.

[19]   Z. Ali, Z. Abbas, and S. Abbas, “Investigation of high vibration phenomena in steam turbine: An experimental exploration into root causes and material analysis,” Advanced Materials & Sustainable Manufacturing, vol. 1, no. 1, 2024, Art. no. 10007, doi: 10.35534/amsm.2024.10007.

[20]   H. A. K. Ali, A. A. Nayeeif, Z. K. Hamdan, and F. A. Abdulla, “Simulation of a suspension control system using a semi-active (MR) damper actuator,” AIP Conference Proceedings, vol. 2866, 2023, Art. no. 050003, doi: 10.1063/5. 0149159.

[21]   N. A. Jebur, H. A. K. Ali, M. A. Abdulrazzaq, F. A. Abdulla, and Z. K. Hamdan, “Investigation of various damping pads effect on vibration,” AIP Conference Proceedings, vol. 2866, 2023, Art. no. 050001, doi: 10.1063/5.0148204.

[22]   N. Jebur and W. Soud, “Recent advances in journal bearings: Wear fault diagnostics, condition monitoring and fault diagnosis methodologies,” Engineering and Technology Journal, vol. 42, no. 2, pp. 125–135, 2024, doi: 10.30684/etj.2024.148997.1737.

[23]   F. Rahmani, E. Makki, and J. Giri, “Influence of bearing wear on the stability and modal characteristics of a flexible rotor supported on powder-lubricated journal bearings,” Lubricants, vol. 11, no. 9, pp. 1–17, 2023, doi: 10.3390/ lubricants11090355.

[24]   L. Cui, D. Wang, C. Zhang, and X. Wang, “A study on the influence of the rotating speed and load on the grain structure and wear properties of bearing steel GCr15 during bearing service,” Metals, vol. 14, no. 12, pp. 1–17, 2024, doi: 10.3390/met14121408.

[25]   R. V. Daniel, S. A. Siddhappa, S. B. Gajanan, S. V. Philip, and P. S. Paul, “Effect of bearings on vibration in rotating machinery,” IOP Conference Series: Materials Science and Engineering, vol. 225, no. 1, Art. no. 012264, 2017, doi: 10.1088/1757-899X/225/1/012264.

[26]   W. Meslameni and T. Kamoun, “Detection of an imbalance fault by vibration monitoring: Case of a screw compressor,” Journal of Applied Research on Industrial Engineering, vol. 8, no. 1, pp. 27–39, 2021, doi: 10.22105/jarie.2021. 269384.1243.

Full Text: PDF

DOI: 10.14416/j.asep.2025.07.012

Refbacks

  • There are currently no refbacks.


Copyright © 2025 by King Mongkut’s University of Technology North Bangkok. All rights reserved.